I like to start in a corner so that I can work in strips across the room. These will make the next steps more manageable. I do not like to cut strips on the entire floor all at once. Just cut one strip and work on it, then cut and repeat. It gives your back a break from bending over and cutting and it gives your knees or bottom a break from sitting and scraping if you do it that way.
After you have cut the flooring in a section, you will want to remove the top layer of linoleum. Just grab the corner and pull. Mostly the top layer only will come up, but there might be places where the glue is worn that also come up with just a little tug. Now it is time to pull out that heat gun.
Nice and simple! For the flooring, I used the high setting. Turn the heat gun on and aim it at the old linoleum that is left behind when pulling off the top. Slowly move the heat gun back-and-forth over the small section to heat it.
Then turn the gun off and scrape the warmed linoleum off the floor with your putty knife. It will just curl right off the floor in very satisfying little strips. After that piece is gone, heat a new small section and repeat. Easy as that. To keep things moving along, I held the Dual Temperature Heat gun in my left hand and putty scraper in my right hand. It kept me from putting the hot gun down on the floor and made it easy to heat and scrape and heat and scrape.
Instead I let it run continuously for about 15 minutes. After it cooled about 60 minutes it turned back on and worked great. The subfloor under the toilet and next to the tub had suffered from water damage and was destroyed. So after scraping the first half of the room, we realized we needed to completely remove the subfloor and replace it to give our bathroom floor a strong, solid surface for the new flooring.
After using the HomeRight Dual Temperature Heat Gun to easily remove linoleum, you are going to love all the other things you can do with it. The two heat settings makes is super useful around the house. This site uses Akismet to reduce spam. Learn how your comment data is processed. We had the square floor tiles like those you see in older elementary classrooms. Almost all of the tiles lifted easily with the exception of a small section and all were handled with correct protocol and disposal.
We were pretty sure the adhesive had asbestos and were following those guidelines. I tried removal with water and a scraper and it was so difficult and laborious that we looked at other solutions and came up with WD which kept the asbestos from becoming airborne, softened the glue - actually made it a black oil to tar like substance.
If done in sections it can be left overnight so the WD does all the work, otherwise you will need to use a scraper and wire brush to lift the tar from the subfloor. Follow that with Prep sol to remove the oil from WD application. I would not recommend this on any floor that has sheetrock butted against the floor as the oil will seep into the sheetrock. This is not a project for the faint of heart. I just finished removing three layers of vinyl from the sq ft of floor in the kitchen of my '82 house, tested and there was no asbestos.
The top layer was fairly easy as they had stapled a wood underlayment on top of the two existing glued down layers. Keep our complete kitchen demo guide on hand for your next project. Have thoughts on this topic? Head over to Twitter or Facebook and use dumpstersblog to join the conversation.
Learn to safely tear down your front porch via our guide that walks you through the steps, from removing the roof to tearing out the floor. Find out which home improvement projects you can do yourself and which ones are better left to a professional. Need a Dumpster? Call Go. How to Remove Vinyl or Linoleum Flooring in 4 Easy Steps When vinyl and linoleum are installed over a wood subfloor, which is the case in most homes, the most time-consuming aspect is removing the adhesive left behind—which we cover in step four.
What do you think? Related Articles. How to Remove a Porch From Roof to Foundation Learn to safely tear down your front porch via our guide that walks you through the steps, from removing the roof to tearing out the floor. Use a scraper tool for delicate linoleum. For delicate floors, scrape the adhesive or underlayment with a scraper tool. You may need to apply moderate to extreme pressure depending on the strength of the adhesive.
This can be very time consuming, but it doesn't risk damaging hardwood subfloors. You may, however, find that it's difficult to get the oscillating scraper blade underneath the adhesive. Either way, the heat gun softens the adhesive and makes it easier to remove. Heat the adhesive for durable subfloors. For more durable subfloors, soak the adhesive with boiling hot water and allow it to absorb for approximately 15 minutes.
Again, only apply water if the subfloor is concrete or a replaceable plywood. Wood warping may occur with any type of water application so be careful when dealing with salvageable hardwood subfloors. Here's how you get the boiling water onto the adhesive or underlayment without creating an absolute mess or, even worse, flooding. Line sections of the floor with towels — towels you're okay with losing. Pour the hot water over the towels, letting the towels absorb most of the water but heat up the adhesive anyway.
Wait 15 minutes before removing the towels. You can also cut the floor open in several places using a sharp blade and pour a stripping material into the gaps to help loosen the linoleum. Next scrape away with a manual scraper. You'll want a larger scraper for moistened adhesive, as it comes off much easier than dry adhesive, giving you plenty of opportunity to take a wider berth.
Use a wallpaper steamer. For a neat trick, try using a wallpaper steamer. Get the steamer warmed up. Place the applicator pad of the steamer over one section of the adhesive and let it steam for 60 to 90 seconds. Move the steamer to an adjacent section and scrape off the section where the applicator just was. This process is pretty quick compared to the dry method of removing adhesive.
A square foot floor should take less than two hours. Part 3. Apply a chemical stripper. You can apply a chemical stripper to any stubborn adhesive per the manufacturer's instructions. Most chemical strippers use the same active ingredients that are found in paint strippers and can be purchased at your local hardware store.
Scrape the treated adhesive. Scrape away the treated adhesive with a putty knife to remove any existing material. Since most of the adhesive should have been removed before the stripper was deployed, this process should be fairly easy. Sweep or vacuum the newly exposed subfloor. This is important to remove any small debris. Your subfloor is officially ready to shine in a new skin! Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow.
Mark Spelman Construction Professional. Mark Spelman. Support wikiHow by unlocking this expert answer. Not Helpful 2 Helpful 3. Not Helpful 6 Helpful 5. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.
New tile, Pergo or vinyl floor covering may be installed directly over existing linoleum if the old floor is smooth and firmly affixed. Helpful 53 Not Helpful Flooring products and adhesives applied prior to may contain asbestos, so proper precautions must be when tearing, breaking or sanding questionable material. Helpful 34 Not Helpful Provide adequate ventilation and follow all safety instructions when utilizing chemical strippers.
Helpful 19 Not Helpful You Might Also Like How to. How to.
0コメント