If you can not plug it in, chances are that you have an older, non-earthed outlet; contact an electrician to have it replaced with an earthed outlet. Do not use an adapter to defeat the earthing.
If the cable becomes damaged or frayed, replace it immediately. Generally, the total ratings of all equipment plugged into any one power line should not exceed 15 amperes. Help Guide hlp2. Do not make any adjustments other than those outlined in the handbook, you might cause damage requiring extensive repair work. For graphics or charts, it's best to use the single-sheet path top feed. Note: If you have paper in the paper path, be sure to remove it before installing rear-feed paper.
Pull up on the lock levers and open the tractor covers. Grasp the paper separator, lift it slightly, pull back on it, then swing it forward. Move the right tractor over to fit the width of the paper. Adjust the right tractor to centre the paper holes on the pins, and push back the lock lever.
The paper feeds into the printer. Note: The standard setting for the Top of Form where the printing begins is 2. To change the setting, see page 9. Read Me First rmf3. Place the first two holes in the paper over the tractor pins on either side and close the tractor covers. Open the carriage cover and lift the paper separator to the single-sheet position. Use the single-sheet path for letterhead stationery, memos, and individual envelopes.
It is recommended for printing graphs and charts because it provides the most accurate control of the paper. Note: If you have continuous-form paper in the path, press the PARK button to remove it before loading single sheets. Make sure the printer is on and deselected SEL light off. Make sure the printer is deselected SEL light off. To change the setting, see the next column. The paper will feed into the printer. Page 11 3. Press SEL to re-select the printer.
Turn the printer off. Press SEL to deselect the printer. Press LF to change the position of the Top of Form. Tear off any printed pages. Press PARK. Move the paper separator to the single-sheet feed position.
Place the wire feed guide in the paper separator. Place a sheet of paper in the paper separator. To switch from single-sheet feed to continuous forms: 1. Lower the paper separator into the continuous-forms position and swing the wire feed guide over onto the pull-up roller. Make sure paper is loaded.
To stop the test: If you wish to stop the test before it is complete, press SEL. Press TEAR consecutively until the emulation you wish to select prints in the right-hand column. SET NU 6. See your software documentation for information on how to select a printer driver. If you have the wrong driver selected, you will see strange characters, incorrect fonts, etc.
Press LF. Remove and discard the used ribbon cartridge. Make sure the printer is turned OFF. The printhead may be HOT! Unpack the new ribbon cartridge. P Help Guide hlp3. Install the new ribbon cartridge. Turn the printer OFF and use the platen knob to back the paper all the way out. Open the access cover, and remove the pull-up roller assembly. Remove any torn pieces of paper. Turn the printer on. Replace the pull-up roller assembly, and close the access cover. Reload paper.
Fold some continuous-form paper over three times to make a page four sheets thick, load it on the tractors and close the covers. Swing the paper separator over, and use the platen knob to draw the quadruple-thick page around the platen: this brings out any jammed bits of paper. Swing the paper separator over, reload regular paper, and lower the paper separator back into place. Remove the paper pieces, and use the platen knob to back the paper out. Page 20 Single-Sheet Jams 4.
Remove any torn pieces from around the carriage. Reinstall the pull-up roller assembly, and close the access cover. Use the platen knob to back the jammed paper out. Open the access cover and remove the pull-up roller assembly. Turn the printer on, and reload paper. Note: Never use solvents or strong detergents on the cabinet: they could damage the housing. Turn the printer off, and remove any paper from the path. Open the access cover, remove the pull-up roller assembly.
Use a clean, dry cloth to dust around the carriage shaft and platen. Remove any loose bits of paper. Help Guide hlp3. Problem: Nothing happens when I turn on the printer. Solution: 1 Check to be sure that the printer driver you have selected in your software matches the printer emulation. Solution: Check the power cable connection and power outlet to your printer. If you are using a power strip, make sure it is turned on, and that the fuse has not blown nor the circuit breaker tripped.
Problem: The printer does not print when data is sent. Solutions: 1 Is the SEL light on? If not, press the SEL key. Solution: This indicates a paper jam. The initialisation string contains codes that override the panel and menu settings. Solution: This indicates that the paper lever is set at the wrong position for the paper you are trying to use: move it to the proper setting.
Solution: Try turning the printer off and then back on again. If the light still blinks, call for service. To change your printer to ignore the reset code, enter the Menu Mode, go down to the Set-Up group and change the setting for Reset Inhibit to Yes see Menu Mode later in this manual.
The I-Prime signal will automatically override any front panel settings you have made. To eliminate this problem, enter the Menu Mode, go down to the Parallel Interface group and change the setting for I-Prime to Invalid see Menu Mode later in this manual.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. All rights reserved. First edition March Written and produced by the Documentation Department. Epson is a registered trademark of Epson America, Inc. Safety Your Oki printer has been carefully designed to give you years of safe, reliable performance.
Help Guide i. Contents Safety Menu Mode: Control Panel Help Guide iii. Centre the printhead. The printhead may be HOT! Remove and discard the used ribbon cartridge. Unpack the new ribbon cartridge. Help Guide 1. Install the new ribbon cartridge. Turn the printer OFF and use the platen knob to back the paper all the way out. Remove any torn pieces of paper. Turn the printer on. Reload paper. Help Guide 3.
Correcting Repetitive Rear-Feed Jams If the paper keeps jamming, you probably have bits of paper stuck in the paper path. Help Guide 5. You can only view or download manuals with. Sign Up and get 5 for free. Combined: Enable the combination of the code page and the language conversion. Code Page Only: Enable the code page only and suppress the language Only use genuine original consumables to ensure the best quality and performance from your hardware.
Do not change the ribbon cartridge with the power switch set to Make sure the printer is turned OFF. Page 43 Unpack the new ribbon cartridge. Install the new ribbon cartridge. Turn the knob 1 in the direction of the arrow to take up any ribbon slack. Do not turn the knob anticlockwise as the ribbon might jam. Set the printer Power Switch to OFF and disconnect the power cable from the printer before cleaning the printer.
Keep the access cover closed to avoid the possibility of detergent entering the printer. Page 45 Use a clean, dry cloth to dust around the carriage shaft and platen. Remove any loose pieces of paper. Installation instructions are supplied with the accessories. Open the access cover, and remove the pull-up roller assembly. Remove any torn pieces of paper. Replace the pull-up roller assembly, and close the access cover. Reload paper. Perform steps through under "Rear-feed jams". Fold some continuous-form paper over three times to make a page four sheets thick, load it on the tractors and close the covers.
Page 49 Swing the paper separator over, and use the platen knob to draw the quadruple- thick page around the platen: this brings out any jammed bits of paper.
Remove the paper pieces, and use the platen knob to back the paper out. Swing the paper separator over, reload regular paper, and lower the paper separator back into place. Use the platen knob to back the jammed paper out. Open the access cover and remove the pull-up roller assembly.
Remove any torn pieces from around the carriage. Reinstall the pull-up roller assembly, and close the access cover. Turn the printer on and reload paper.
If you are using a power strip, make sure it is turned on, and that the fuse has not blown nor the circuit breaker tripped. Try separator. Ink smears on paper.
0コメント